Ja. Ik geloof dat nu alles werkt. Bedankt.
Translation:
Yes, I think everything works now. Thanks.
Search found 7 matches
- Tue Jan 02, 2024 5:11 am
- Forum: Opentherm Gateway Forum
- Topic: OTGW monitor displays Bad Request messages
- Replies: 4
- Views: 1034
- Mon Jan 01, 2024 6:48 pm
- Forum: Opentherm Gateway Forum
- Topic: OTGW monitor displays Bad Request messages
- Replies: 4
- Views: 1034
Re: OTGW monitor displays Bad Request messages
Doesn't work for me (with the web server on port 80)
None of the three proposed codes, entered via the Miscellaneous tab, work properly. Each time the command GW=1 gives the following response:
HTTP/1.1 400 Bad Request
For example:
None of the three proposed codes, entered via the Miscellaneous tab, work properly. Each time the command GW=1 gives the following response:
HTTP/1.1 400 Bad Request
For example:
- Mon Jan 01, 2024 10:20 am
- Forum: Opentherm Gateway Forum
- Topic: OTGW monitor displays Bad Request messages
- Replies: 4
- Views: 1034
OTGW monitor displays Bad Request messages
For example, when entering the command GW=1, the OT monitor gives the answer: HTTP/1.1 400 Bad Request
What is going on here?
What is going on here?
- Sun Dec 31, 2023 10:40 am
- Forum: Suggestions, Questions & Feedback
- Topic: OTGW between eTwist and Elga Ace causes problems
- Replies: 0
- Views: 681
OTGW between eTwist and Elga Ace causes problems
I bought an OTGW at Nodo shop. Ready-made programmed and with WiFi. I placed this between the Remeha eTwist (without gateway) and the Elga Ace. The transistor 1 of the PCB immediately burned out, because the R-bus of the Elga apparently (sometimes) emits too high voltages and that R-bus does not aut...
- Sun Dec 31, 2023 10:32 am
- Forum: Suggestions, Questions & Feedback
- Topic: OTGW print between eTwist and Elga burns out
- Replies: 5
- Views: 3940
Re: OTGW print between eTwist and Elga burns out
May I assume the measurements you reported were done with the boiler and thermostat disconnected? In that case the voltages you found are normal. The OTGW consists of 2 electrically isolated parts: The main part with the processor and thermostat interface, and the boiler interface. The boiler inter...
- Fri Dec 22, 2023 5:47 am
- Forum: Suggestions, Questions & Feedback
- Topic: OTGW print between eTwist and Elga burns out
- Replies: 5
- Views: 3940
OTGW print between eTwist and Elga burns out
I bought an OTGW board with installed WiFi and firmware from Nodo shop. I hung this between my eTwist thermostat and my Elga Ace heat pump. But the PCB burned out at transistor 1. Nodo shop put the print back in order, after which the GTWO was reattached with the greatest care. Although just before ...
- Thu Dec 21, 2023 6:30 pm
- Forum: Opentherm Gateway Forum (NL)
- Topic: OTGW-print tussen eTwist en Elga brandt door
- Replies: 1
- Views: 827
OTGW-print tussen eTwist en Elga brandt door
Ik heb een OTGW-print met geïnstalleerde wifi en firmware gekocht bij Nodo-shop. Deze heb ik tussen mijn eTwist thermostaat en mijn Elga Ace warmtepomp gehangen. Maar de print brandde door bij transistor 1. Nodo shop heeft de print weer op orde gemaakt, waarna met de grootste zorgvuldigheid de GTWO ...