Email sending with HCB firmware 1.6.0-1026

Forum about Xanura, Eaton Holec and Marmitek and other brand X10 and A10 devices.
Post Reply
LeonH
Starting Member
Starting Member
Posts: 4
Joined: Mon Jan 14, 2013 3:58 pm

Email sending with HCB firmware 1.6.0-1026

Post by LeonH »

Did anyone succeed in sending an email with the Home Control Box with firmware 1.6.0-1026?
It's not clear why my settings don't work. I use my account at Planet Internet.
SMTP server: mail.planet.nl or smtp.kpnmail.nl ?
SMTP poort: 25 or 587 ?
Authenticatie: on or off ?

Nothing works :x

Please help...
Akatar
Senior Member
Senior Member
Posts: 1134
Joined: Thu Nov 22, 2007 12:25 am
Location: the netherlands

Re: Email sending with HCB firmware 1.6.0-1026

Post by Akatar »

misschien:

SMTP: mail.kpnmail.nl
LeonH
Starting Member
Starting Member
Posts: 4
Joined: Mon Jan 14, 2013 3:58 pm

Re: Email sending with HCB firmware 1.6.0-1026

Post by LeonH »

I tried this one also. However i'm searching for the right combination of settings: SMT server, SMT poort, Authenticatie etc.
Henk
Member
Member
Posts: 450
Joined: Sat May 06, 2006 10:54 pm
Location: Netherlands

Re: Email sending with HCB firmware 1.6.0-1026

Post by Henk »

My settings are:

smtp.xs4all.nl
smtp port 25
authenticatie vink on
TLS vink on
Use a valid Email adres to send your test email
Use username of your provider
Use password
Click on test and check the emailadres

It may help to restart the HCB.

good luck Henk
LeonH
Starting Member
Starting Member
Posts: 4
Joined: Mon Jan 14, 2013 3:58 pm

Re: Email sending with HCB firmware 1.6.0-1026

Post by LeonH »

Ok Henk, thanx.
I tried the settings as you suggested. However, no results.
I used these settings:
Smtp server: mail.planet.nl
Smtp poort: 25
Afzender adres: my emailadres
Authenticatie: on
TLS: on
Gebruikersnaam: gebruikersnaam
Wachtwoord: xxxxx

After pressing the button TEST I get the message: Versturen test e-mail niet gelukt: Server niet gevonden
I use Logmein software (remote control) to get connected with the HCB, this works fine.
What am I doing wrong???
Henk
Member
Member
Posts: 450
Joined: Sat May 06, 2006 10:54 pm
Location: Netherlands

Re: Email sending with HCB firmware 1.6.0-1026

Post by Henk »

Try to do a complete reset .... so save the configuration (export) remove power / turn on and import the saved configuration and try it again ...
if not working let me know ..... Henk
LeonH
Starting Member
Starting Member
Posts: 4
Joined: Mon Jan 14, 2013 3:58 pm

Re: Email sending with HCB firmware 1.6.0-1026

Post by LeonH »

Ok, I will give it a try. I keep you posted :-)
riham
Starting Member
Starting Member
Posts: 1
Joined: Wed Dec 03, 2014 9:51 am

Re: Email sending with HCB firmware 1.6.0-1026

Post by riham »

Only the top half my switch controls this all, the bottom half of the swith does nothing. By keep pressing the top half of the switch, the light cycles through dim and bright.
Are you worried about 70-685 exam dump prep and testking.co.uk - 1Y0-400 dumps Check out our latest resources for ccna braindump and muih
Post Reply

Return to “X10, A10 Xanura Marmitek Forum”