Latest additions to RFXtrx433 firmware
Moderator: b_weijenberg
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Latest additions to RFXtrx433 firmware
Latest additions to RFXtrx433 firmware
RGB LED strip controller
With Lighting5 you can control dx.com RGB controllers
This one has a learn option and any ID can be used.
http://dx.com/p/rf-remote-touch-rgb-controller-130913
This one has a fixed ID and the ID of the remote must be used
http://dx.com/p/wireless-touch-panel-re ... ight-67412
Maverick ET732 Barbecue dual sensor
http://www.amazon.com/Maverick-Et-732-R ... B004IMA718
Livolo touch switch and dimmer
http://www.aliexpress.com/store/all-who ... 00715.html
be sure to select the RF version!
Elro - Byron SX chimes
http://www.chbyron.eu/Byron/ByronSXRange/68/89/
Revolt NC-5462 Energycounter
http://www.pearl.de/a-NC5462-5452.shtml
It is not advised to use this module if other 433.92MHz devices are used because this sensor transmits with a very short interval of about 4 seconds and the risk to disturb other RF traffic is too high.
Alecto SA30 smoke detector
http://www.alecto.nl/rookmelder-3-stuks-linkable
OWL CM180i sensor (3 phase current and total power usage)
http://www.planete-domotique.com/transm ... n-owl.html
http://www.planete-domotique.com/pince- ... ndard.html (10mm 71Amp)
http://www.planete-domotique.com/pince- ... large.html (17mm 200Amp)
RGB LED strip controller
With Lighting5 you can control dx.com RGB controllers
This one has a learn option and any ID can be used.
http://dx.com/p/rf-remote-touch-rgb-controller-130913
This one has a fixed ID and the ID of the remote must be used
http://dx.com/p/wireless-touch-panel-re ... ight-67412
Maverick ET732 Barbecue dual sensor
http://www.amazon.com/Maverick-Et-732-R ... B004IMA718
Livolo touch switch and dimmer
http://www.aliexpress.com/store/all-who ... 00715.html
be sure to select the RF version!
Elro - Byron SX chimes
http://www.chbyron.eu/Byron/ByronSXRange/68/89/
Revolt NC-5462 Energycounter
http://www.pearl.de/a-NC5462-5452.shtml
It is not advised to use this module if other 433.92MHz devices are used because this sensor transmits with a very short interval of about 4 seconds and the risk to disturb other RF traffic is too high.
Alecto SA30 smoke detector
http://www.alecto.nl/rookmelder-3-stuks-linkable
OWL CM180i sensor (3 phase current and total power usage)
http://www.planete-domotique.com/transm ... n-owl.html
http://www.planete-domotique.com/pince- ... ndard.html (10mm 71Amp)
http://www.planete-domotique.com/pince- ... large.html (17mm 200Amp)
Re: Latest additions to RFXtrx433 firmware
nice additions!
Re: Latest additions to RFXtrx433 firmware
Bert,
Is the Alecto "koolmoxide meter" COA-22 also incluided?
Regards,
Arjo.
Is the Alecto "koolmoxide meter" COA-22 also incluided?
Regards,
Arjo.
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Re: Latest additions to RFXtrx433 firmware
As far as I know the COA-22 is not equiped with RF
Re: Latest additions to RFXtrx433 firmware
very nice additions, braking News for domoticaland. Integration of systems is a bad understood principle for some domotica suppliers but of the essence for their survival. I dont have 20 usb ports on my computer while some manufaturers think that. i dont want 20 wifi networks in my house but one. 1 wifi network can just cope with my family's demands of tablets, phones and computers. And i dont have the time nor the money to buy 20 different systems. And 20 different apps to monitor is also not what i expect from domotica. And least of all i want 30 remote controls in my house.That is what i like from rfxcom the underlying idea is integration= standardization .
Re: Latest additions to RFXtrx433 firmware
Nice way of telling the new additions
Keep up the good work
Keep up the good work
Running HS3PRO on PC with Z-Wave / OpenTherm / Plugwise / RFXcom / MQTT / XAP400 / Logitech Media Server and Squeezelite on PI`s
Re: Latest additions to RFXtrx433 firmware
Great...
@ bert,
Are all the divices from livolo [ eu version 433Mhz ] supported?
And the give no bomb signal?
operate these switches as kaku versions.
Whether they work on the Zwave way.
I mean, so they give a 433MHz signal when I use them manually? [ i ordered 2 of these, 1 duo switch and 1 dimmer ]
How does the dimmer works?
This is a dimmer switch fitted as an old-fashioned?
Or should this dimmer dimming all lights a kaku or Zwave, with a extra lampmodule?
@ bert,
Are all the divices from livolo [ eu version 433Mhz ] supported?
And the give no bomb signal?
operate these switches as kaku versions.
Whether they work on the Zwave way.
I mean, so they give a 433MHz signal when I use them manually? [ i ordered 2 of these, 1 duo switch and 1 dimmer ]
How does the dimmer works?
This is a dimmer switch fitted as an old-fashioned?
Or should this dimmer dimming all lights a kaku or Zwave, with a extra lampmodule?
Re: Latest additions to RFXtrx433 firmware
FYIb_weijenberg wrote:Latest additions to RFXtrx433 firmware
Elro - Byron SX chimes
http://www.chbyron.eu/Byron/ByronSXRange/68/89/
domoticaforum.eu/viewtopic.php?f=27& ... 322#p66973
-
- Starting Member
- Posts: 1
- Joined: Sat Sep 08, 2012 2:07 pm
Re: Latest additions to RFXtrx433 firmware
Good update.
After upgrading the firmware to release 71 the Oregon EW109 is correctly reporting the temp/humidity info.
I do have some issues getting the
I'm using the RGB TRC02 in the lighting 5 tab of the RFXmngr, but I don't know how to properly identify the fixed ID of the remote.
I do receive some of the rf signals send from the remote (some buttons pressed do not show up in the RFXmngr).
These are the codes that I'm receiving:
Probably it is a matter of identifying the proper fixed ID of the remote, but until now I have been unsuccesful....
After upgrading the firmware to release 71 the Oregon EW109 is correctly reporting the temp/humidity info.
I do have some issues getting the
to work.This one has a fixed ID and the ID of the remote must be used
http://dx.com/p/wireless-touch-panel-re ... ight-67412
I'm using the RGB TRC02 in the lighting 5 tab of the RFXmngr, but I don't know how to properly identify the fixed ID of the remote.
I do receive some of the rf signals send from the remote (some buttons pressed do not show up in the RFXmngr).
These are the codes that I'm receiving:
- 0703011A12010040 [OFF]
0703011B12010080 [DIM -]
0703011C11010480 [Color wheel]
0703011D11010880 [Color wheel]
0703011E11010A00 [Color wheel]
Probably it is a matter of identifying the proper fixed ID of the remote, but until now I have been unsuccesful....
Re: Latest additions to RFXtrx433 firmware
@ Bert,
This remote is supported?
nl.aliexpress.com/item/LIVOLO-Digital-W ... 44807.html
He is the brand Livolo ..
I got it, but can not get it working
This remote is supported?
nl.aliexpress.com/item/LIVOLO-Digital-W ... 44807.html
He is the brand Livolo ..
I got it, but can not get it working
Re: Latest additions to RFXtrx433 firmware
Livolo can't be received by the RFXtrx. It can only transmit the livolo code.
Re: Latest additions to RFXtrx433 firmware
My apologies for the dumb question but isn`t that the same for Byron , Home Easy or COCO units as all are one way rf switches, that you can only transmit code to them but you don`t expect a feedback ?!.. if there is something I am missing I would really appreciate if you explained it.mbliek wrote:Livolo can't be received by the RFXtrx. It can only transmit the livolo code.
All the best,
- b_weijenberg
- Forum Moderator
- Posts: 1744
- Joined: Sun May 14, 2006 4:32 pm
- Location: Netherlands
Re: Latest additions to RFXtrx433 firmware
Byron chime button, Home Easy and COCO remotes are received by the RFXtrx433, Livolo remotes are not received.
See also the RFXtrx User Guide.pdf chapter 2.2 which protocols are transmit only.
See also the RFXtrx User Guide.pdf chapter 2.2 which protocols are transmit only.