Page 1 of 1
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Sun May 03, 2009 9:34 pm
by Noel
I'm getting the following error in my HomeSeer startup<blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote">Error RFXCOM Input Sensor 1 is not the Input Sensor Message Panel! Assign another device code to Input Sensor 1<hr height="1" noshade id="quote"></font id="quote"></blockquote id="quote">I'm sure it's fixed easely, but how?
Thank you.
--
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Sun May 03, 2009 10:39 pm
by Antoon
I think you have used the first input device for another device while it is reserved for the sensor message panel.
- Antoon
<h6>
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Mon May 04, 2009 7:56 am
by Noel
Hi Antoon,
It's set to the sensor message panel (it did this by it self).
I'll remove all the panel sensor's and see if it will fix it.
--
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Mon May 04, 2009 8:12 am
by Noel
Hmmm not so nice. I can not delete the [1 to [4 sensors.
I get a "RFXCOM system panels can not be deleted."
This is what I have from [1 to [4
<blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote">Alarm Panel State [1 System RFXCOM Alarm Panel State ALARM[1]Q
Alarm Panel Status [2 System RFXCOM Alarm Panel Status ALARM[2]Q
Alarm Panel Display [3 System RFXCOM Alarm Panel Messages ALARM[3]Q
Alarm Panel Control [4 System RFXCOM Alarm Panel Control ALARM[4]Q<hr height="1" noshade id="quote"></font id="quote"></blockquote id="quote">
--
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Mon May 04, 2009 10:16 am
by b_weijenberg
Input Sensor Message Panel is different device than the security panels.
You should change the Input sensor having address 1 and assign another device number to that sensor using MOFIFY in the RFXCOM - Input Dev. configuration panel.
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Mon May 04, 2009 11:32 am
by Noel
I do not have anything assigned to address 1 in RFXcom > Input Dev.
The 1st sensor in Input Dev. starts with nr. \6
In RFXcom > Security I do have [1, but that can not be modified or deleted.
--
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Tue May 05, 2009 9:24 am
by b_weijenberg
I suppose that after removing all DooNetwork devices that where using the RFXCOM Input devices house code including \1 the problem is solved?
help: Input Sensor 1 is not the Input Sensor Message Panel
Posted: Tue May 05, 2009 9:55 am
by Noel
re: I suppose that after removing all DooNetwork devices that where using the RFXCOM Input devices house code including \1 the problem is solved?
Yes.
For some reason one of my DooNetwork devices also got a \1 house code.
After your suggestion of removing it, it fixed the problem.
Recreating the DooNetwork device gave it a housecode of ^1
Once again thank you for your help.
PS: Please note that I did NOT give ANY of my devices a house code! They all get generated by the software!
--